VoIP Mobility
Made Simple
Quick Setup Guide v3.0
Wherever Business Grows
Package Contents
IP Phone, handset and
handset cable Power adaptor 2m Ethernet Cable
Desktop Phone Stand Wall Mount Stand
Labels
Locating the IP Phone
Desktop Installation
1.
Insert the two alignment pins of the Desktop Phone Stand into the sockets as shown.
2.
Push the stand toward the top of the IP Phone until it clicks into place. NOTE:
Only the Desktop Phone Stand is required for desktop installation.
Wall Mount Installation
For installation ease, use the following illustrations to correctly wall mount the
Syspine IP Phone.
NOTE:
The handset hook is supplied in the upright position, suitable for desktop or wall mounting. If the phone is installed on a desktop without the stand, remove
the hook and install it point down.
Hardware Setup
The section that follows describes how to install the Syspine IP Phone.
Syspine IP Phone 310
Basic connections
Locate the rear view of the IP Phone and make all the necessary connections as
follows.
3
Connecting the IP Phone After connecting the A50 Plus to the LAN and a suitable power outlet, connect
all the required IP Phones at once to the LAN.
The IP Phone supports daisy-chain connection for limited port access
using the supplied Ethernet cable.
Perform the following steps to connect the IP Phone as part of a daisy-chain:
1.
Disconnect the existing LAN cable from the PC. 2.
Plug the LAN cable into the LAN port on the IP Phone. 3.
Using the supplied Ethernet cable, connect the PC port on the IP Phone to the LAN port on the PC.
4.
Using the supplied power cables for each phone, connect the IP Phones to a power source.
5.
Record the IP address for each phone as displayed on the LCD screen. Important:
The Syspine IP Phone is designed specifically to work in conjunction with the Syspine A50 Plus.
Connect to LAN
Connect to PC
Connect to power outlet
Connect to phone
handset
LAN PC
Connect to LAN
Connect
to PC
1.
Insert the two alignment pins of the Wall Mount Stand in to the sockets on the phone.
2.
Push the stand toward the bottom of the IP Phone to until it clicks into place.
3.
Locate a clean, even wall space with adequate room for cabling.
4.
Drill a hole and insert a suitable wall-fixing plug. 5.
Insert a suitable screw and tighten until approximately 5 mm (0.2 inch) is visible.
6.
Align the wall-mounting slot on the underside of the IP Phone with the screw.
7.
Place the IP Phone on the wall and pull down to locate the screw securely.
DC 12V
+ LAN PC -
Desktop stand
socket
Handset
connection port
Wall mount
stand socket
Wall mount
socket
Desktop stand
socket
Wall mount
stand socket
If port access is not a consideration and a daisy chain connection is not required,
attach the IP Phone directly to the LAN switch with the supplied cable.
NOTE:
• If the IP address is not displayed, enter # 47 (# IP) on the keypad to display the IP address.
•
If the IP Phone is connected through a Power over Ethernet (PoE) device, it is not necessary to connect the power adapter.
®
Wall Mount Stand
I
MPORTANT NOTICE: PLEASE READ CAREFULLY •
Power, network or telephone service outages: If there is an outage, disruption, or other degradation of the power, network or telephone services at your location, Syspine A50 Plus will not work.
•
Maintain an alternative means of calling 911: You should maintain a backup means of calling 911 emergency services (for example, by using a phone plugged into a standard telephone line or a cell
phone) in case of a power failure, telephone service outage, or other problem that may inhibit you
from using Syspine A50 Plus.
•
Calling emergency services using a VoIP service provider: Please note that not all VoIP service providers enable users to call emergency services. Such requirements vary by country. If you have
questions about this capability, please contact your VoIP service provider.
•
How to dial 911: Please inform all of your employees, visitors, and Syspine A50 Plus users that they can dial 9 plus the emergency number, to access emergency services.
Emergency-number location obligations that may apply to certain owners of Syspine A50 Plus:
Your telephone company or voice/VoIP service provider may be required under applicable law to
provide a telephone number and address associated with that telephone number to emergency
services when a caller dials an emergency number. Further, certain countries’ laws may require the
owner/operator of a multi-line telephone system (MLTS), such as Syspine A50 Plus, to provide
emergency services with the physical location/address of the phone that was used to call an
emergency number, in addition to the caller’s telephone number. In such cases, compliance with such
MLTS laws is your responsibility. Please note that Syspine A50 Plus does not provide to emergency
services with the physical location/address of a phone that is used to call an emergency number.
